Total
560 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2021-0216 | 1 Juniper | 3 Acx5448, Acx710, Junos | 2024-02-04 | 3.3 LOW | 6.5 MEDIUM |
| A vulnerability in Juniper Networks Junos OS running on the ACX5448 and ACX710 platforms may cause BFD sessions to flap when a high rate of transit ARP packets are received. This, in turn, may impact routing protocols and network stability, leading to a Denial of Service (DoS) condition. When a high rate of transit ARP packets are exceptioned to the CPU and BFD flaps, the following log messages may be seen: bfdd[15864]: BFDD_STATE_UP_TO_DOWN: BFD Session 192.168.14.3 (IFL 232) state Up -> Down LD/RD(17/19) Up time:11:38:17 Local diag: CtlExpire Remote diag: None Reason: Detect Timer Expiry. bfdd[15864]: BFDD_TRAP_SHOP_STATE_DOWN: local discriminator: 17, new state: down, interface: irb.998, peer addr: 192.168.14.3 rpd[15839]: RPD_ISIS_ADJDOWN: IS-IS lost L2 adjacency to peer on irb.998, reason: BFD Session Down bfdd[15864]: BFDD_TRAP_SHOP_STATE_UP: local discriminator: 17, new state: up, interface: irb.998, peer addr: 192.168.14.3 This issue only affects the ACX5448 Series and ACX710 Series routers. No other products or platforms are affected by this vulnerability. This issue affects Juniper Networks Junos OS: 18.2 versions prior to 18.2R3-S8 on ACX5448; 18.3 versions prior to 18.3R3-S5 on ACX5448; 18.4 versions prior to 18.4R1-S6, 18.4R3-S7 on ACX5448; 19.1 versions prior to 19.1R3-S5 on ACX5448; 19.2 versions prior to 19.2R2, 19.2R3 on ACX5448; 19.3 versions prior to 19.3R3 on ACX5448; 19.4 versions prior to 19.4R3 on ACX5448; 20.1 versions prior to 20.1R2 on ACX5448; 20.2 versions prior to 20.2R2 on ACX5448 and ACX710. | |||||
| CVE-2021-0289 | 1 Juniper | 229 Acx1000, Acx1100, Acx2000 and 226 more | 2024-02-04 | 2.9 LOW | 5.3 MEDIUM |
| When user-defined ARP Policer is configured and applied on one or more Aggregated Ethernet (AE) interface units, a Time-of-check Time-of-use (TOCTOU) Race Condition vulnerability between the Device Control Daemon (DCD) and firewall process (dfwd) daemons of Juniper Networks Junos OS allows an attacker to bypass the user-defined ARP Policer. In this particular case the User ARP policer is replaced with default ARP policer. To review the desired ARP Policers and actual state one can run the command "show interfaces <> extensive" and review the output. See further details below. An example output is: show interfaces extensive | match policer Policer: Input: __default_arp_policer__ <<< incorrect if user ARP Policer was applied on an AE interface and the default ARP Policer is displayed Policer: Input: jtac-arp-ae5.317-inet-arp <<< correct if user ARP Policer was applied on an AE interface For all platforms, except SRX Series: This issue affects Juniper Networks Junos OS: All versions 5.6R1 and all later versions prior to 18.4 versions prior to 18.4R2-S9, 18.4R3-S9 with the exception of 15.1 versions 15.1R7-S10 and later versions; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; This issue does not affect Juniper Networks Junos OS versions prior to 5.6R1. On SRX Series this issue affects Juniper Networks Junos OS: 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.4 versions prior to 19.4R3-S4; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect 18.4 versions prior to 18.4R1 on SRX Series. This issue does not affect Junos OS Evolved. | |||||
| CVE-2021-0257 | 1 Juniper | 18 Ex9200, Junos, Mx10 and 15 more | 2024-02-04 | 3.3 LOW | 6.5 MEDIUM |
| On Juniper Networks MX Series and EX9200 Series platforms with Trio-based MPCs (Modular Port Concentrators) where Integrated Routing and Bridging (IRB) interfaces are configured and mapped to a VPLS instance or a Bridge-Domain, certain Layer 2 network events at Customer Edge (CE) devices may cause memory leaks in the MPC of Provider Edge (PE) devices which can cause an out of memory condition and MPC restart. When this issue occurs, there will be temporary traffic interruption until the MPC is restored. An administrator can use the following CLI command to monitor the status of memory usage level of the MPC: user@device> show system resource-monitor fpc FPC Resource Usage Summary Free Heap Mem Watermark : 20 % Free NH Mem Watermark : 20 % Free Filter Mem Watermark : 20 % * - Watermark reached Slot # % Heap Free RTT Average RTT 1 87 PFE # % ENCAP mem Free % NH mem Free % FW mem Free 0 NA 88 99 1 NA 89 99 When the issue is occurring, the value of “% NH mem Free” will go down until the MPC restarts. This issue affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines), including MX-MPC1-3D, MX-MPC1E-3D, MX-MPC2-3D, MX-MPC2E-3D, MPC-3D-16XGE, and CHAS-MXxx Series MPCs. No other products or platforms are affected by this issue. This issue affects Juniper Networks Junos OS on MX Series, EX9200 Series: 17.3 versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R3-S3; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.2 versions prior to 20.2R1-S3, 20.2R2; 20.3 versions prior to 20.3R1-S1,, 20.3R2. This issue does not affect Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R3-S2; 18.1; 18.2 versions prior to 18.2R3-S4; 18.3 versions prior to 18.3R3-S2; 18.4 versions prior to 18.4R3-S1; 19.1; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2. | |||||
| CVE-2021-0243 | 1 Juniper | 2 Ex4300, Junos | 2024-02-04 | 3.3 LOW | 4.7 MEDIUM |
| Improper Handling of Unexpected Data in the firewall policer of Juniper Networks Junos OS on EX4300 switches allows matching traffic to exceed set policer limits, possibly leading to a limited Denial of Service (DoS) condition. When the firewall policer discard action fails on a Layer 2 port, it will allow traffic to pass even though it exceeds set policer limits. Traffic will not get discarded, and will be forwarded even though a policer discard action is configured. When the issue occurs, traffic is not discarded as desired, which can be observed by comparing the Input bytes with the Output bytes using the following command: user@junos> monitor interface traffic Interface Link Input bytes (bps) Output bytes (bps) ge-0/0/0 Up 37425422 (82616) 37425354 (82616) <<<< egress ge-0/0/1 Up 37425898 (82616) 37425354 (82616) <<<< ingress The expected output, with input and output counters differing, is shown below: Interface Link Input bytes (bps) Output bytes (bps) ge-0/0/0 Up 342420570 (54600) 342422760 (54600) <<<< egress ge-0/0/1 Up 517672120 (84000) 342420570 (54600) <<<< ingress This issue only affects IPv4 policing. IPv6 traffic and firewall policing actions are not affected by this issue. This issue affects Juniper Networks Junos OS on the EX4300: All versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.1 versions prior to 19.1R3-S3; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2. | |||||
| CVE-2021-0224 | 1 Juniper | 1 Junos | 2024-02-04 | 3.3 LOW | 6.5 MEDIUM |
| A vulnerability in the handling of internal resources necessary to bring up a large number of Layer 2 broadband remote access subscriber (BRAS) nodes in Juniper Networks Junos OS can cause the Access Node Control Protocol daemon (ANCPD) to crash and restart, leading to a Denial of Service (DoS) condition. Continued processing of spoofed subscriber nodes will create a sustained Denial of Service (DoS) condition. When the number of subscribers attempting to connect exceeds the configured maximum-discovery-table-entries value, the subscriber fails to map to an internal neighbor entry, causing the ANCPD process to crash. This issue affects Juniper Networks Junos OS: All versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R2-S13; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R3-S8; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R2. | |||||
| CVE-2021-0260 | 1 Juniper | 1 Junos | 2024-02-04 | 7.5 HIGH | 7.3 HIGH |
| An improper authorization vulnerability in the Simple Network Management Protocol daemon (snmpd) service of Juniper Networks Junos OS leads an unauthenticated attacker being able to perform SNMP read actions, an Exposure of System Data to an Unauthorized Control Sphere, or write actions to OIDs that support write operations, against the device without authentication. This issue affects: Juniper Networks Junos OS: 17.2 version 17.2R1 and later versions; 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S12, 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R2-S5, 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S6, 19.2R2; 19.3 versions prior to 19.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R1. | |||||
| CVE-2021-0237 | 1 Juniper | 11 Ex4300-mp, Ex4600, Ex4650 and 8 more | 2024-02-04 | 3.3 LOW | 6.5 MEDIUM |
| On Juniper Networks EX4300-MP Series, EX4600 Series, EX4650 Series, QFX5K Series deployed as a Virtual Chassis with a specific Layer 2 circuit configuration, Packet Forwarding Engine manager (FXPC) process may crash and restart upon receipt of specific layer 2 frames. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on EX4300-MP Series, EX4600 Series, EX4650 Series, QFX5K Series 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4, 17.4R3-S5; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2; | |||||
| CVE-2021-0256 | 1 Juniper | 1 Junos | 2024-02-04 | 2.1 LOW | 5.5 MEDIUM |
| A sensitive information disclosure vulnerability in the mosquitto message broker of Juniper Networks Junos OS may allow a locally authenticated user with shell access the ability to read portions of sensitive files, such as the master.passwd file. Since mosquitto is shipped with setuid permissions enabled and is owned by the root user, this vulnerability may allow a local privileged user the ability to run mosquitto with root privileges and access sensitive information stored on the local filesystem. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S12, 17.4 versions prior to 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.3 versions prior to 18.3R3-S4; 19.1 versions prior to 19.1R3-S4; 19.3 versions prior to 19.3R3-S1, 19.3R3-S2; 19.4 versions prior to 19.4R2-S3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S3, 20.2R2, 20.2R3. | |||||
| CVE-2021-0273 | 1 Juniper | 9 Acx5800, Ex9200, Junos and 6 more | 2024-02-04 | 5.0 MEDIUM | 5.3 MEDIUM |
| An always-incorrect control flow implementation in the implicit filter terms of Juniper Networks Junos OS and Junos OS Evolved on ACX5800, EX9200 Series, MX10000 Series, MX240, MX480, MX960 devices with affected Trio line cards allows an attacker to exploit an interdependency in the PFE UCODE microcode of the Trio chipset with various line cards to cause packets destined to the devices interfaces to cause a Denial of Service (DoS) condition by looping the packet with an unreachable exit condition ('Infinite Loop'). To break this loop once it begins one side of the affected LT interfaces will need to be disabled. Once disabled, the condition will clear and the disabled LT interface can be reenabled. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue only affects LT-LT interfaces. Any other interfaces are not affected by this issue. This issue affects the following cards: MPCE Type 3 3D MPC4E 3D 32XGE MPC4E 3D 2CGE+8XGE EX9200 32x10G SFP EX9200-2C-8XS FPC Type 5-3D FPC Type 5-LSR EX9200 4x40G QSFP An Indicator of Compromise (IoC) can be seen by examining the traffic of the LT-LT interfaces for excessive traffic using the following command: monitor interface traffic Before loop impact: Interface: lt-2/0/0, Enabled, Link is Up Encapsulation: Logical-tunnel, Speed: 100000mbps Traffic statistics: Current delta Input bytes: 3759900268942 (1456 bps) [0] <---------- LT interface utilization is low Output bytes: 3759900344309 (1456 bps) [0] <---------- LT interface utilization is low After loop impact: Interface: lt-2/0/0, Enabled, Link is Up Encapsulation: Logical-tunnel, Speed: 100000mbps Traffic statistics: Current delta Input bytes: 3765160313129 (2158268368 bps) [5260044187] <---------- LT interface utilization is very high Output bytes: 3765160399522 (2158266440 bps) [5260055213] <---------- LT interface utilization is very high This issue affects: Juniper Networks Junos OS on ACX5800, EX9200 Series, MX10000 Series, MX240, MX480, MX960. Versions 15.1F6, 16.1R1, and later versions prior to 16.1R7-S8; 17.1 versions prior to 17.1R2-S12; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R1-S7, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S4, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S1, 19.4R2. This issue does not affect the MX10001. This issue does not affect Juniper Networks Junos OS versions prior to 15.1F6, 16.1R1. Juniper Networks Junos OS Evolved on ACX5800, EX9200 Series, MX10000 Series, MX240, MX480, MX960 19.4 versions prior to 19.4R2-EVO. This issue does not affect the MX10001. | |||||
| CVE-2021-0234 | 1 Juniper | 2 Junos, Qfx5100-96s | 2024-02-04 | 5.0 MEDIUM | 5.8 MEDIUM |
| Due to an improper Initialization vulnerability on Juniper Networks Junos OS QFX5100-96S devices with QFX 5e Series image installed, ddos-protection configuration changes will not take effect beyond the default DDoS (Distributed Denial of Service) settings when configured from the CLI. The DDoS protection (jddosd) daemon allows the device to continue to function while protecting the packet forwarding engine (PFE) during the DDoS attack. When this issue occurs, the default DDoS settings within the PFE apply, as CPU bound packets will be throttled and dropped in the PFE when the limits are exceeded. To check if the device has this issue, the administrator can execute the following command to monitor the status of DDoS protection: user@device> show ddos-protection protocols error: the ddos-protection subsystem is not running This issue affects only QFX5100-96S devices. No other products or platforms are affected by this issue. This issue affects: Juniper Networks Junos OS on QFX5100-96S: 17.3 versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R3-S4; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R3-S2; 18.4 versions prior to 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R3, 19.1R3-S4; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2; | |||||
| CVE-2021-0275 | 1 Juniper | 24 Ex2300, Ex2300-c, Ex3400 and 21 more | 2024-02-04 | 9.3 HIGH | 8.8 HIGH |
| A Cross-site Scripting (XSS) vulnerability in J-Web on Juniper Networks Junos OS allows an attacker to target another user's session thereby gaining access to the users session. The other user session must be active for the attack to succeed. Once successful, the attacker has the same privileges as the user. If the user has root privileges, the attacker may be able to gain full control of the device. This issue affects: Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S15 on EX Series; 12.3X48 versions prior to 12.3X48-D95 on SRX Series; 15.1 versions prior to 15.1R7-S6 on EX Series; 15.1X49 versions prior to 15.1X49-D200 on SRX Series; 16.1 versions prior to 16.1R7-S7; 16.2 versions prior to 16.2R2-S11, 16.2R3; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3-S1; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3; 19.1 versions prior to 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S3, 19.2R2; 19.3 versions prior to 19.3R2. | |||||
| CVE-2021-0227 | 1 Juniper | 22 Junos, Srx100, Srx110 and 19 more | 2024-02-04 | 5.0 MEDIUM | 7.5 HIGH |
| An improper restriction of operations within the bounds of a memory buffer vulnerability in Juniper Networks Junos OS J-Web on SRX Series devices allows an attacker to cause Denial of Service (DoS) by sending certain crafted HTTP packets. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. When this issue occurs, web-management, NTP daemon (ntpd) and Layer 2 Control Protocol process (L2CPD) daemons might crash. This issue affects Juniper Networks Junos OS on SRX Series: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2; | |||||
| CVE-2021-0252 | 1 Juniper | 4 Junos, Nfx150, Nfx250 and 1 more | 2024-02-04 | 4.6 MEDIUM | 7.8 HIGH |
| NFX Series devices using Juniper Networks Junos OS are susceptible to a local code execution vulnerability thereby allowing an attacker to elevate their privileges via the Junos Device Management Daemon (JDMD) process. This issue affects Juniper Networks Junos OS on NFX Series: 18.1 version 18.1R1 and later versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S5, 19.2R2. This issue does not affect: Juniper Networks Junos OS versions prior to 18.1R1. This issue does not affect the JDMD as used by Junos Node Slicing such as External Servers use in conjunction with Junos Node Slicing and In-Chassis Junos Node Slicing on MX480, MX960, MX2008, MX2010, MX2020. | |||||
| CVE-2021-0269 | 1 Juniper | 1 Junos | 2024-02-04 | 5.1 MEDIUM | 8.8 HIGH |
| The improper handling of client-side parameters in J-Web of Juniper Networks Junos OS allows an attacker to perform a number of different malicious actions against a target device when a user is authenticated to J-Web. An attacker may be able to supersede existing parameters, including hardcoded parameters within the HTTP/S session, access and exploit variables, bypass web application firewall rules or input validation mechanisms, and otherwise alter and modify J-Web's normal behavior. An attacker may be able to transition victims to malicious web services, or exfiltrate sensitive information from otherwise secure web forms. This issue affects: Juniper Networks Junos OS: All versions prior to 17.4R3-S3; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2. | |||||
| CVE-2021-0293 | 1 Juniper | 1 Junos | 2024-02-04 | 2.1 LOW | 5.5 MEDIUM |
| A vulnerability in Juniper Networks Junos OS caused by Missing Release of Memory after Effective Lifetime leads to a memory leak each time the CLI command 'show system connections extensive' is executed. The amount of memory leaked on each execution depends on the number of TCP connections from and to the system. Repeated execution will cause more memory to leak and eventually daemons that need to allocate additionally memory and ultimately the kernel to crash, which will result in traffic loss. Continued execution of this command will cause a sustained Denial of Service (DoS) condition. An administrator can use the following CLI command to monitor for increase in memory consumption of the netstat process, if it exists: user@junos> show system processes extensive | match "username|netstat" PID USERNAME PRI NICE SIZE RES STATE C TIME WCPU COMMAND 21181 root 100 0 5458M 4913M CPU3 2 0:59 97.27% netstat The following log message might be observed if this issue happens: kernel: %KERN-3: pid 21181 (netstat), uid 0, was killed: out of swap space This issue affects Juniper Networks Junos OS 18.2 versions prior to 18.2R2-S8, 18.2R3-S7. 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S1; 19.4 versions prior to 19.4R1-S4, 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2; This issue does not affect Juniper Networks Junos OS versions prior to 18.2R1. | |||||
| CVE-2021-0242 | 1 Juniper | 2 Ex4300, Junos | 2024-02-04 | 6.1 MEDIUM | 6.5 MEDIUM |
| A vulnerability due to the improper handling of direct memory access (DMA) buffers on EX4300 switches on Juniper Networks Junos OS allows an attacker sending specific unicast frames to trigger a Denial of Service (DoS) condition by exhausting DMA buffers, causing the FPC to crash and the device to restart. The DMA buffer leak is seen when receiving these specific, valid unicast frames on an interface without Layer 2 Protocol Tunneling (L2PT) or dot1x configured. Interfaces with either L2PT or dot1x configured are not vulnerable to this issue. When this issue occurs, DMA buffer usage keeps increasing and the following error log messages may be observed: Apr 14 14:29:34.360 /kernel: pid 64476 (pfex_junos), uid 0: exited on signal 11 (core dumped) Apr 14 14:29:33.790 init: pfe-manager (PID 64476) terminated by signal number 11. Core dumped! The DMA buffers on the FPC can be monitored by the executing vty command 'show heap': ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 4a46000 268435456 238230496 30204960 11 Kernel 1 18a46000 67108864 17618536 49490328 73 Bcm_sdk 2 23737000 117440512 18414552 99025960 84 DMA buf <<<<< keeps increasing 3 2a737000 16777216 16777216 0 0 DMA desc This issue affects Juniper Networks Junos OS on the EX4300: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. | |||||
| CVE-2021-0295 | 1 Juniper | 5 Junos, Qfx10000, Qfx10002 and 2 more | 2024-02-04 | 2.9 LOW | 6.1 MEDIUM |
| A vulnerability in the Distance Vector Multicast Routing Protocol (DVMRP) of Juniper Networks Junos OS on the QFX10K Series switches allows an attacker to trigger a packet forwarding loop, leading to a partial Denial of Service (DoS). The issue is caused by DVMRP packets looping on a multi-homed Ethernet Segment Identifier (ESI) when VXLAN is configured. DVMRP packets received on a multi-homed ESI are sent to the peer, and then incorrectly forwarded out the same ESI, violating the split horizon rule. This issue only affects QFX10K Series switches, including the QFX10002, QFX10008, and QFX10016. Other products and platforms are unaffected by this vulnerability. This issue affects Juniper Networks Junos OS on QFX10K Series: 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 version 18.2R1 and later versions; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S9, 18.4R3-S8; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S7, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2. | |||||
| CVE-2021-0248 | 1 Juniper | 4 Junos, Nfx150, Nfx250 and 1 more | 2024-02-04 | 7.5 HIGH | 10.0 CRITICAL |
| This issue is not applicable to NFX NextGen Software. On NFX Series devices the use of Hard-coded Credentials in Juniper Networks Junos OS allows an attacker to take over any instance of an NFX deployment. This issue is only exploitable through administrative interfaces. This issue affects: Juniper Networks Junos OS versions prior to 19.1R1 on NFX Series. No other platforms besides NFX Series devices are affected. | |||||
| CVE-2021-0254 | 1 Juniper | 1 Junos | 2024-02-04 | 7.5 HIGH | 9.8 CRITICAL |
| A buffer size validation vulnerability in the overlayd service of Juniper Networks Junos OS may allow an unauthenticated remote attacker to send specially crafted packets to the device, triggering a partial Denial of Service (DoS) condition, or leading to remote code execution (RCE). Continued receipt and processing of these packets will sustain the partial DoS. The overlayd daemon handles Overlay OAM packets, such as ping and traceroute, sent to the overlay. The service runs as root by default and listens for UDP connections on port 4789. This issue results from improper buffer size validation, which can lead to a buffer overflow. Unauthenticated attackers can send specially crafted packets to trigger this vulnerability, resulting in possible remote code execution. overlayd runs by default in MX Series, ACX Series, and QFX Series platforms. The SRX Series does not support VXLAN and is therefore not vulnerable to this issue. Other platforms are also vulnerable if a Virtual Extensible LAN (VXLAN) overlay network is configured. This issue affects Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R2, 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1. | |||||
| CVE-2021-0233 | 1 Juniper | 3 Acx4000, Acx500, Junos | 2024-02-04 | 5.0 MEDIUM | 7.5 HIGH |
| A vulnerability in Juniper Networks Junos OS ACX500 Series, ACX4000 Series, may allow an attacker to cause a Denial of Service (DoS) by sending a high rate of specific packets to the device, resulting in a Forwarding Engine Board (FFEB) crash. Continued receipt of these packets will sustain the Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on ACX500 Series, ACX4000 Series: 17.4 versions prior to 17.4R3-S2. | |||||